35kg/m³ XPE foam is a cross-linked polyethylene foam with a nominal density of 35 kilograms per cubic meter. In practical terms, this density describes how much foam material is contained in a given volume; it does not, by itself, define every aspect of performance. I consider 35kg/m³ XPE a balanced specification for projects that need lightweight cushioning, moisture resistance, thermal insulation, and a relatively stable closed-cell structure without selecting a very high-density grade.
At Juchuang Baichuan, I help construction, real estate, packaging, and industrial buyers evaluate 35kg/m³ XPE foam according to thickness, dimensions, surface requirements, compression behavior, temperature conditions, and intended use. The most suitable specification depends on the application rather than density alone. Buyers should confirm technical requirements with samples and project-specific testing before placing a production order.
The value of 35kg/m³ means that one cubic meter of the foam has a nominal mass of approximately 35 kilograms. Density is normally expressed in kilograms per cubic meter, or kg/m³, and is measured according to an agreed sampling and testing method. Because production tolerances, thickness, and test conditions can affect the measured result, buyers should request the supplier’s stated tolerance and test method rather than treating the nominal value as an exact universal figure.
Density can influence firmness, resilience, compressive response, and handling weight, but it is only one part of the specification. A 35kg/m³ sheet may perform differently from another 35kg/m³ sheet if the products use different cross-linking conditions, cell structures, thicknesses, or surface treatments. For this reason, I recommend evaluating density together with compression performance, dimensional stability, water absorption, thermal behavior, and appearance.
XPE foam is made from polyethylene that has been cross-linked and expanded into a fine-cell structure. Its closed-cell construction can limit the movement of water and air through the material compared with many open-cell foams. This makes it useful where a project requires a clean, lightweight layer for cushioning, separation, insulation, or surface protection.
The foam can absorb and distribute some impact energy, helping reduce direct contact between protected surfaces. Actual cushioning performance depends on thickness, load, impact speed, temperature, and the number of loading cycles. I do not recommend selecting 35kg/m³ XPE only because of its density when the application involves heavy equipment, repeated high-energy impacts, or regulated safety requirements.
XPE foam has low thermal conductivity relative to many dense solid materials, so it can function as a supplementary insulation or separation layer. However, the exact insulation value must be confirmed from product-specific test data because thermal performance changes with density, thickness, temperature, and aging. Its closed-cell structure also gives it useful resistance to incidental moisture, although joints, edges, punctures, and installation details can determine the overall moisture performance of a finished system.
At a nominal density of 35kg/m³, the material is generally easier to cut, transport, and install than heavier solid alternatives. It can be supplied in rolls, sheets, strips, profiles, or fabricated parts, depending on the equipment and production plan. The foam can also help separate finished surfaces during storage and transportation, reducing the risk of abrasion when the thickness and surface finish are correctly selected.
In construction, 35kg/m³ XPE foam may be considered for floor underlayment, expansion or separation layers, pipe and duct protection, roof or wall accessory components, and protective packaging for building materials. Its value is often practical: it provides a lightweight layer between surfaces while supporting basic cushioning, insulation, and moisture-resistance requirements. The final suitability should be checked against building codes, fire requirements, acoustic targets, and the complete assembly design.
For flooring projects, XPE foam can be used beneath selected floor systems to provide cushioning, surface separation, and limited thermal or acoustic assistance. The required thickness and compression behavior depend on the floor type, traffic level, subfloor condition, and installation method. If the product will be installed beneath a rigid floor or used in a high-load commercial environment, I recommend confirming long-term compression and dimensional stability before approval.
35kg/m³ XPE foam is suitable for protecting furniture, glass-related components, metal parts, panels, appliances, and other products during handling. It can be die-cut, laminated, slit, or fabricated into inserts when the project requires a more precise fit. Buyers should specify whether the priority is scratch protection, impact cushioning, separation, appearance, or reusable packaging, because these goals may require different thicknesses and formats.
Juchuang Baichuan contains other products and information you need, so please check it out.
The material may also be used for trim protection, seals, gaskets, vibration-reduction components, pipe wrapping, and equipment separation. These uses require careful review of temperature exposure, chemical contact, compression set, flame behavior, and bonding compatibility. A general-purpose 35kg/m³ grade should not automatically be treated as suitable for every automotive or industrial environment.
| Specification | Why It Matters | Buyer Question |
|---|---|---|
| Nominal density | Indicates material mass per volume and supports grade comparison. | What is the allowable density tolerance? |
| Thickness | Influences cushioning, insulation, compression, and installation fit. | What thickness tolerance is required? |
| Width and length | Affect yield, waste, packaging, and production efficiency. | Can the supplier produce the required roll or sheet size? |
| Compression behavior | Helps assess support, recovery, and long-term load response. | Is compression testing available for the intended thickness? |
| Surface and color | Influence appearance, lamination, printing, and installation quality. | Are smooth, embossed, laminated, or custom-color options available? |
| Fire and temperature requirements | May determine whether the material can be used in a regulated assembly. | Which project standards and test documents apply? |
As a practical example, a 10mm-thick layer has a different mechanical role from a 2mm protective sheet even when both are made at 35kg/m³. A 1m³ volume at the nominal density would weigh approximately 35kg, while the weight of a finished roll or sheet depends on its area and thickness. Buyers should therefore compare products using the complete specification rather than price per roll alone.
I begin by identifying whether the foam must cushion impacts, separate surfaces, reduce heat transfer, limit moisture contact, absorb vibration, or provide a combination of functions. This step prevents a common purchasing mistake: choosing a density before defining the actual operating conditions. The project brief should include load, contact surface, installation method, expected service environment, and replacement or maintenance expectations.
Thickness is often as important as density because it controls the available compression distance and the physical fit within the assembly. Rolls may improve installation efficiency for long areas, while sheets or die-cut parts may be more suitable for fixed shapes and protective inserts. I can help buyers compare standard and customized dimensions based on drawings, packaging layouts, or construction details.
A sample allows the buyer to inspect cell consistency, surface finish, flexibility, odor, color, cutting behavior, and compatibility with adhesives or laminates. For construction applications, the sample should be assessed in the proposed assembly rather than alone. Where performance is critical, the buyer should arrange appropriate third-party or project testing instead of relying only on a supplier’s general product description.
Before approval, I recommend requesting a technical data sheet, packing information, available dimensions, production tolerance, minimum order quantity, lead-time estimate, and inspection procedure. Buyers should also clarify whether the supplier can maintain consistent density and thickness across repeat orders. Clear documentation reduces misunderstandings between procurement teams, installers, engineers, and logistics partners.
As a manufacturer and exporter, Juchuang Baichuan can support B2B buyers with product selection, size confirmation, sample coordination, packaging discussions, and production planning for 35kg/m³ XPE foam. My approach is to match the foam construction to the application instead of presenting density as a standalone solution. Depending on the project, I can discuss roll, sheet, strip, laminated, die-cut, or other fabricated formats subject to technical and production review.
For an efficient inquiry, please provide the target density, thickness, width, length, color, estimated quantity, application, delivery destination, and any required testing or compliance conditions. Drawings, photographs, packaging samples, or assembly details can make the evaluation more accurate. I will then help identify a practical specification and clarify which performance points need verification before mass production.
35kg/m³ XPE foam can be a practical mid-density option for buyers seeking a lightweight closed-cell material with cushioning, separation, moisture-resistance, and supplementary insulation functions. It is especially worth considering for construction accessories, flooring-related layers, protective packaging, and fabricated industrial components. Nevertheless, the correct decision depends on the complete design rather than the 35kg/m³ label alone.
My recommended next step is to send the application conditions and required dimensions to Juchuang Baichuan for a preliminary specification review. We can then confirm sample requirements, production feasibility, documentation, and commercial details before you approve a larger order. This process gives procurement and engineering teams a clearer basis for deciding whether 35kg/m³ XPE foam fits the project.
If you are looking for more details, kindly visit 35kg/m³ XPE Foam.